Full list of messages displayed by the controller

Sabaj-System TV lifts are equ­ip­ped with a con­trol box, which is the heart of the whole device. The con­troller is visi­ble from the out­side in almost all models, the­re­fore we have atta­ched a display to it, which will allow you to easily com­mu­ni­cate with the lift. Here we have col­lec­ted all the error codes that may appear during use.

Error codes clas­si­fi­ca­tions

Not all codes may apply to your model of lift. If you have our most advan­ced model, the Roto­lift with Auto­lid auto­ma­tic lid ope­ning sys­tem, then you sho­uld defi­ni­tely review these hints. Because of the four-way motion and the Auto­lid sys­tem, you may see the most mes­sa­ges on this model.

The con­trol box display may inform you of obvious actions, like pro­gram­ming or move­ment in a cer­tain direc­tion. It will also display appro­priate sym­bols if it detects an obstacle in its path, too much load or loose cables. In this case, you can use the prompts we have pre­pa­red in the third column.

Mes­sa­ges for all types of lifts:

Display	Explanation	Solution
	Safety system activated	1. Remove possible obstacles in the furniture space underneath the TV 2. The system is only active when lowering 3. The system will automatically calibrate itself every 30 cm during each descent 4. The sensitivity of the system depends on the weight of the TV (approximately 5-15 kg)
	The lift's limit switch cable harness disconnected	1. Check the connection of the 10 PIN harness between the lift and the control box 2. Check the condition of the wiring in the harness plug on the control unit and limit switch side (broken wire, pin sticking out, plug not pushed in, damaged braid or wires)
	The lift electric motor overload	Lower the lift's load
	The lift's wiring disconnected	Check all connections of the controller harness and lift's motor. Some may have been loosened during assembly
	Full motion reset
	No impulses from the lift's motor	1. The lift's lid motor may be blocked 2. Check that the cable connections are not stretched or loose. Because of the many factors involved in this error, it is best to contact technical support at helpdesk@sabaj.pl

Messages only visible during programming:

Display	Explanation	Solution
	Assigning RF remote to control box	Press any button on RF remote to assign, or wait 30 seconds to quit mode
	Assigning IR remote to control box	Press buttons (I) and (II) to program the IR remote control
	UP VP Memory approved
	Down VP Memory approved
	Clockwise (M1) rotation angle approved
	Counter-clockwise (M2) rotation angle approved
	Attempt on setting DOWN VP position before the DOWN limit switch	Use this option only intentionally. It is not recommended to set DOWN VP higher than where the limit switch is located
	Attempt on setting UP VP lower than DOWN VP	Re-set the UP/DOWN settings. This might make the lift unable to move up or down

Rotolift (+ Autolid):

Display	Explanation	Solution
	Autolid limit switch cable harness disconnected	Check all the connections and contacts from AUTOLID to the control box. Some pins might be loose due to transport of furniture fitting
	Furthest clockwise rotation acquired (mechanical stop)
	Furthest counter-clockwise rotation acquired (mechanical stop)
	Central „0” position acquired
	AUTOLID electric motor overload	Lower the AUTOLID load (lid is too heavy)
	AUTOLID's wiring disconnected	Check all the connections and contacts from AUTOLID wiring to the control box. Some pins might be loose due to transport of furniture fitting
	No impulses from lid's motor (Rotolift + Autolid only)	1. The AUTOLID's flap motor may be blocked. 2. Also check that the cable connections are not stretched or loose. Because of the many factors involved in this error, it is best to contact technical support at helpdesk@sabaj.pl
	Rotating movement stopped due to safety	Remove obstacles from the lift's way